P10 Outdoor LED Display
10 mm pixel pitch · 960×960 mm cabinets · 10,000 px/m² · 6,000–10,000 nits · IP65 front & rear maintenance

The Excel LED P10 outdoor LED display line — OK, B and A960 series — is built for billboards, building facades and stadium screens: 960×960 mm cabinets at 25–28 kg, 320×160 mm modules, SMD 3535/2727 lamps with optional DIP, and common-cathode energy saving on the A960 platform. Supplied by Excelled, a trusted LED display manufacturer serving global B2B integrators.

P10 outdoor LED display billboard screens around a public shopping plaza at dusk

Quick Answer: What Is a P10 Outdoor LED Display?

A P10 outdoor LED display is a high-brightness LED screen with a 10 mm pixel pitch — 10,000 pixels per square meter — built for outdoor viewing from roughly 10 m and beyond: billboards, building facades, stadium scoreboards and roadside signage. At this distance it reads sharp, and because it carries a third of the pixels of a P6 screen, it costs less per square meter and burns less power.
• Three Excel LED series make the line: OK (960×960×77 mm aluminum, 28 kg, 6,500 nits), B (960×960 mm magnesium, 28 kg, 6,000 nits, 320×160 modules) and A960 (960×960×88 mm die-cast, 25 kg, ≥6,500 nits, IP66, common-cathode energy saving).
• Standard module: 320×160 mm, 32×16 pixels (512 points), SMD 3535 lamps (confirmed); the A960 platform uses 480×320 mm modules, 48×32 pixels, SMD 2727 Jingtai lamps (confirmed).
• Outdoor protection runs deep: conformal-coated PCB (三防漆), matte black spray-oil mask, 1.2 mm stainless-steel screws, IP65/IP66 cabinets, 3,840 Hz class refresh.
• Logistics: 2-year standard parts & workmanship warranty, 72-hour aging and luminance calibration before packing.

One-Stop Solution

One-Stop Solution of P10 Outdoor LED Displays

The “P10” in the name means the distance between the centers of two neighboring pixels is 10 mm. At that pitch the screen carries 10,000 pixels per square meter, so from 10 m away the picture is smooth while the cost and the power bill stay at large-format levels — the arithmetic behind most highway billboards and facade screens.

Excel LED supplies the P10 outdoor display as one complete system — cabinet, module, power supply and control system — configured, aged and calibrated in the factory, so integrators receive a wall that bolts together on site instead of a kit of parts that must be matched by hand. You order one BOM and one warranty, not four suppliers and four excuses. Series, brightness, brightness-sensors and maintenance modes can be customized to the project.

Where does the P10 sit in the outdoor lineup? Outdoor P8 is finer for 8–10 m viewing, and the P6 and P5 sit above it for closer commercial sites. In our engineering practice, P10 is the pitch advertisers settle on for 15 m+ viewing because it holds visibility without paying fine-pitch prices.

10 mm

Pixel Density

10,000 pixels/m², 96×96 pixels per 960×960 cabinet — the cost-efficient outdoor standard for 10 m+ viewing.

960×960

Cabinet Platform

Aluminum (28 kg), magnesium (28 kg) and die-cast (25 kg) 960×960 builds, 77–88 mm deep, front & rear service options.

IP65/66

Weatherproof Build

IP65–IP66 cabinets, conformal-coated PCB, black spray-oil mask, 1.2 mm stainless screws — rated for sun, rain and salt air.

Single BOM

One Kit, One Warranty

Cabinet + module + power + receiving card configured, aged 72 h and calibrated before packing. Download full electrical and mechanical drawings with your quotation.

Product Snapshot

P10 Outdoor LED Display at a Glance

The structured snapshot below is the sum of the confirmed factory figures on this page — values marked (confirmed) come from the Excel LED series spec tables and the factory module database; (typical) marks industry-standard figures that Excel LED configures per project.

Parameter Specification
Product Type Outdoor fixed LED display — billboards, facades, stadium, signage
Pixel Pitch 10 mm (confirmed)
Pixel Density 10,000 pixels/m² (confirmed)
LED Package SMD 3535 (standard module, confirmed) · SMD 2727 (A960, Jingtai, confirmed) · DIP three-in-one option (typical)
Module Size 320×160 mm (standard, confirmed) · 480×320 mm (A960, confirmed) · 160×160 mm DIP option (typical)
Module Resolution 32×16 px = 512 (320×160) · 48×32 px = 1,536 (480×320) (confirmed)
Cabinet Size 960×960×77 mm (OK, aluminum) · 960×960 mm (B, magnesium) · 960×960×88 mm (A960, die-cast) (confirmed)
Cabinet Resolution 96×96 px on all three platforms (confirmed)
Cabinet Weight 25–28 kg (A960 25 kg · OK/B 28 kg, confirmed)
Maintenance Front & rear (B, A960 confirmed) · Front T-wrench (OK, confirmed; rear on request)
Brightness 6,000 nits (B) · 6,500 nits (OK) · ≥6,500 nits (A960); 10,000-nit option on the A960 platform (confirmed per series)
Refresh Rate 3,840 Hz (OK, A960) · 1,920–3,840 Hz (B) · 7,680 Hz option (A960 broadcast-grade) (confirmed)
Gray Scale 65,536 levels (16 bit) (OK, confirmed) — A960 runs the same driver-class platform
Viewing Angle 140°/140° (OK, confirmed) · 140°/120° (A960, confirmed)
Protection IP65 (OK, B) · IP66 (A960) (confirmed)
Power Consumption B: 800/300 W/m² max/avg · A960: ≤550 / ≤186 W/m² max/avg · OK: 250 W avg / 650 W max per 960×960 cabinet (confirmed per series)
Power Input AC 100–240 V, 50/60 Hz (confirmed)
LED Lamp Brand SMD 3535 (standard, confirmed) · SMD 2727 Jingtai (A960, confirmed) · brand per project BOM
Driver IC / Scan Standard 320×160 module: 512 points with 24 or 48 driver ICs (two factory tiers, confirmed per factory module list); A960 module: 48×32, 1/2 scan (confirmed)
Power Supply Mean Well, G-Energy, Chuanglian — factory-fit with surge and temperature protection (confirmed per LEGIDATECH P10 series)
Control System NovaStar · Huidu · Linsn · Colorlight, all compatible (confirmed on OK series page)
Working Temperature −30 °C to +70 °C (typical, per LEGIDATECH P10 series page)
Lifetime ≥100,000 hours (typical, at factory-rated operating conditions)
Warranty 2-year standard site warranty, parts & workmanship; extended terms available

Series Lineup

P10 Outdoor LED Display Series: OK, B and A960 Platforms

Three Excel LED platforms carry the 10 mm pitch outdoors, each with a different cabinet strategy — choose the platform first, then the module configuration:

Platform OK Series B Series A960 Series
Cabinet 960×960×77 mm 960×960 mm 960×960×88 mm
Material / process Aluminum corners + profile frame — cost-effective fixed installation Magnesium alloy die-cast — light, thermally conductive, fans integrated Die-cast aluminum, hard-connection CNC structure
Weight 28 kg 28 kg 25 kg
Module 320×160 mm 320×160 mm 480×320 mm
Brightness 6,500 nits 6,000 nits ≥6,500 nits (10,000-nit option)
Refresh 3,840 Hz 1,920–3,840 Hz 3,840 / 7,680 Hz
IP IP65 IP65 IP66
Energy 250 W avg / 650 W max (per cabinet) 800/300 W/m² max/avg Common cathode — ≤550/≤186 W/m² max/avg
Maintenance Front (T-wrench); rear on request Front & rear Front & rear
Best for DOOH billboards, price-driven fixed sites Digital signage, facades with on-site splicing focus Energy-tender sites — toll, transit, 24/7 LED walls

P10 OK series 960×960 mm aluminum outdoor LED display cabinet

OK Series — the cost-effective fixed P10

9,216 pixels per cabinet (96×96) at 6,500 nits, IP65, 3,840 Hz, 100/240 V. Checked and budgeted for DOOH; detail on the OK series product page.

P10 B series magnesium outdoor LED display cabinet for DOOH signage

B Series — the universal 320×160 module platform

From P3 to P10, the B series uses the same 320×160 mm module, so a site can upgrade from P4 to P10 later without replacing the cabinet frame. IP65, dual front & rear access, integrated extraction fans. See the B series page for the full table.

P10 A960 common-cathode energy saving outdoor LED screen

A960 — the energy-saving common-cathode P10

480×320 mm die-cast modules, IP66, 1/2 scan, ≤186 W/m² average — the common-cathode architecture cuts power bills sharply against conventional builds. Explore the A960 energy-saving series.

Adjacent outdoor platforms — not exact P10

Two platforms are close to, but not identical with, P10, and we keep them separate so you can compare honestly:

  • A1000 Series (1000×1000 mm, P2.97–P10.42) — hollow aluminum profile, common cathode, matte-black-ink mask, naked-eye 3D splicing. Its closest pitch is P10.42, not exactly P10: choose A1000 when you need 3D capability or a 1000 mm grid, choose OK/B/A960 when the project reads “P10”.
  • ST960 / ST1440 stadium series (P8/FC8) — perimeter and scoreboard screens tuned to sports viewing; for stadium P10 scoreboards the OK or A960 platform covers the projection cabinet side.

Cabinet Sizes & Materials

P10 Outdoor LED Display Cabinet Sizes: 960×960 Standards and Materials

All three P10 platforms share the 960×960 mm standard grid — 18 modules of 320×160 mm (3×6), or 6 modules of 480×320 mm (2×3), per cabinet — with 25–28 kg weights and 77–88 mm depth. The standard grid matters because 960 mm is the wall unit: billboards, facade grids and stadium structures worldwide are dimensioned around it, and replacement cabinets in five years will still bolt on.

Cabinet Material & process Modules · resolution Service access
960×960×77 mm (OK) Aluminum profile frame, 28 kg (confirmed) 18 × 320×160 mm · 96×96 px Front — T-wrench tool-free; rear on request
960×960 mm (B) Magnesium alloy, 28 kg, two integrated extraction fans (confirmed) 18 × 320×160 mm · 96×96 px Front & rear — dual access
960×960×88 mm (A960) Die-cast aluminum, hard-connection CNC structure, 25 kg (confirmed) 6 × 480×320 mm · 96×96 px Front & rear

Materials and processes behind each P10 cabinet

  • Aluminum profile frame (OK). The industrial workhorse — corrosion-resistant, easy to machine to non-standard sizes, and the budget choice for billboard grids where long spans ride on steel structures.
  • Magnesium alloy die-cast (B). Lighter per volume with excellent thermal conductivity, so the cast body acts as a heat spreader and the fans pull heat out without adding an air-conditioning unit — the reason the B series drops its external AC need in most climates.
  • Die-cast aluminum + hard connection (A960). The die-cast mould delivers tight part-to-part dimensional consistency; hard-connection links between modules remove the flexible cables that rattle loose over years of thermal cycling — and they give the flush face needed for floor-level advertising screens and 24/7 transit walls.
  • Steel, for ground-level signage. Where cost outranks weight — bus shelters, pavement signs — the same factory line builds galvanized steel boxes for P10 (typical, on request).
The chain works like this: material and process → dimensional consistency and weight → splicing quality → installation cost → maintenance mode. For a rooftop billboard that cranes in once, aluminum plus a cheaper frame wins; for a facade behind a cladding system, magnesium or die-cast wins on service access and long-term alignment.

P10 outdoor LED display 960x960 mm aluminum cabinet with powered screen sections

Custom cabinet sizes are available on request — send your wall dimensions and we check whether a non-standard format saves you money on a specific layout. LED screen size and dimensions guide covers the free-math behind any grid.

Module Sizes

P10 Outdoor LED Module Sizes and Maintenance: 320×160, 480×320 and DIP Boards

Four P10 module formats sit under the line. The 320×160 mm SMD board is the volume standard — 32×16 pixels, 512 points, 3,840 Hz-class circuit (confirmed); the 480×320 mm die-cast module (A960) carries 48×32 pixels at 1/2 scan (confirmed); DIP boards of 160×160 and 320×160 mm are the classic option when the viewing distance is measured in tens of meters (typical).

Module Resolution · package Maintenance Waterproof treatment
320×160 mm SMD (standard) 32×16 px · 512 points, SMD 3535 lamps, 512 points, 24 or 48 driver ICs (factory tiers), 3,840 Hz-class circuit (confirmed, factory module list) Front & rear — front access on B/A960 builds, swap in minutes Conformal-coated PCB (III-proof), sealed connector area
480×320 mm die-cast (A960) 48×32 px · 1,536 points, SMD 2727 Jingtai lamps, 1/2 scan (confirmed) Front & rear IP66-sealed module face, hard-connection rear
160×160 / 320×160 mm DIP (option) 16×16 / 32×16 px, three-in-one DIP lamps, 5,500–10,000 nits (typical, per LEGIDATECH P10 platform) Rear — classic DIP service access Sealed lamp columns + coated board

The standard P10 board ships in two driver tiers: 24 ICs (the entry configuration for price-first billboards) and 48 ICs (the high-scan configuration for filmed DOOH and camera-critical sites). The exact driver model is set on the BOM per configuration.

Front vs rear maintenance on P10 modules

The module’s service side decides the whole site’s construction cost:

  • Front access — modules pull out from the face with a T-wrench or magnetic release; no service corridor behind the wall, which matters when the screen sits on a rooftop, a facade or against a cladding system.
  • Rear access — where a walkway or gantry exists (stadium perimeter, billboard service ladder), rear access means cheaper modules and central maintenance: swap a module and reach the power and receiving card in one visit.
  • Front & rear on the same cabinet — the B and A960 builds. The maintenance decision happens once, at the design stage; convert to the other method later costs real money.

P10 outdoor LED display 320×160 mm SMD module with 32×16 pixels

PCB & Protection

P10 PCB Board Thickness and Protection

The module board is the part nobody sees and the reason some outdoor screens die in three years while others survive ten. Three things decide it: board thickness, the coating on the board, and the screws that hold it.

PCB option Typical plates Why it matters at P10
0.8 mm Flexible / semi-flexible FR-4 (typical) Used for soft and curved P10 boards where bending matters more than rigidity
1.0 mm Standard rigid FR-4 class (typical) The volume choice for P10 outdoor modules — enough stiffness to stay flat across 160 mm while keeping module weight and cost down
1.2 mm Heavy-duty rigid (typical) High-wind, high-vibration sites — a stiffer board resists module flex that cracks solder joints

Why outdoor P10 modules need conformal coating (三防漆)

Every outdoor P10 module in this line is conformal-coated (“three-proof” lacquer / 三防漆) before assembly — a thin protective film over the whole board, including the solder joints and the copper traces that the mask does not expose. It solves a specific failure chain: humidity and condensation enter a screen through the smallest joint, migrate along the board, and create electrolytic corrosion between the power traces — the classic cause of the “one module dies, then its neighbors” cascade on outdoor walls.

The coating blocks moisture and the salt-laden air of coastal sites; the board’s connector area stays sealed separately, and the driver IC layout puts the ICs on the cooling path rather than in the humidity pocket. This is why a conformal-coated outdoor P10 module exists at all — and why a “waterproof” claim on the datasheet is meaningless without the process behind it.

Four outdoor can-never-use factors: conformal coating on the PCB; 1.2 mm stainless-steel screws for every module-to-frame and frame-to-structure joint — stainless because coated steel screws will oxidize after the first summer storms, 1.2 mm because the thin head seats flush under the mask without stress-marks; sealed connector zones; and a black spray-oil finish on the mask (next section). Non-corrosive hardware is what keeps a screen serviceable after five years when cheap zinc-plated screws are welded shut with rust.

Thickness, copper and thermal path

Copper thickness scales with the current the board carries; a P10 standard module runs around 4–5 A per 5 V line, so the power path is sized to keep that drop low — no exact copper weight is published per configuration and the board drawing ships with your quote. The thermal rule of thumb: heats are managed by the driver IC layout and cabinet fans, the board never carries the heat load alone.

Mask & Surface

P10 LED Mask and Surface Treatment: Black Spray-Oil Finishing

The mask — the black plastic face the lamps sit inside — is the second-most-guarded surface on an outdoor module, because under sunlight it decides contrast. The LED mask on this line uses a black spray-oil finishing process to improve the visual uniformity and contrast of the display: the spray film levels the plastic’s micro-texture, cuts specular reflection of the sun, and makes the unlit face of the panel sit closer to the “off” black of the lamps themselves.

Mask treatment Effect on the picture
Black spray-oil (面罩喷黑油) Uniform black face, no glossy hotspots — the surface between lamps reads as one continuous dark field, so the black level and contrast rise
Matte black ink (A1000 series) Combat glare under direct sunlight — the same family of treatment, applied to the 3D platform; the A1000 3D LED screen documents it as “specialized matte black ink”
Uncoated black plastic (industry baseline) Sunlight scatters off the raw plastic — gray-wash between pixels, lower effective contrast at high ambient light

Why it matters for P10 specifically: at 10 mm pitch the light-emitting area is roughly a quarter of the panel surface, so the non-lit 75% of the face determines the black level as much as the lamps do. With a 6,000–6,500-nit panel facing bright morning sun, a mask without the black-oil finish reads washed out by mid-morning; the treated face holds the picture. Mask geometry — lamp pockets angled per the viewing window, no flat shelf where dust sits — completes the design.

P10 LED display mask closeup with black spray-oil finishing between lamp beads

LED Package

P10 LED Package: DIP vs SMD Module Comparison

At P10 the lamp package question is a real fork, not marketing noise. DIP — the through-hole lamp with the visible body and large footprint — spent twenty years as the only outdoor option; SMD took over most sites as its brightness and reliability closed the gap. Both remain in production because the sites are genuinely different.

Item DIP (three-in-one / 1.8 mm class) SMD (3535 / 2727)
Brightness Typically strong — 5,500–10,000 nits, lamp body adds direct light High, configuration dependent — 6,000–10,000 nits on this line
Viewing angle Typically narrower (directional beam) Typically wider (140°/140° class)
Cost per m² Lower at equal pixel count Higher, but dropping as supply scales
Failure mode Lamp-by-lamp repair on site Module swap normal; single-lamp repair rare
Dust / moisture path Lamp body stands above the mask; deeper sealing tests Sealed modules, conformal-coated boards dominate
Typical use Long-distance billboards — 25 m+ viewing, price-first tenders General outdoor commercial — facades, DOOH, stadium (this line’s default)

The honest conclusion: nothing is “better” in absolute terms. A P10 DIP screen viewed from 60 m at night cannot show any advantage for SMD; a facade viewed from 12 m demands the wide viewing angle and uniformity of SMD. Excel LED supplies both — SMD is the factory default on the OK/B/A960 platforms; DIP is offered on request and documented on the LEGIDATECH P10 platform (B-Pro, 10.667 mm, three-in-one DIP, exceptionally bright and wide for events).

P10 outdoor DIP LED module displaying vibrant color content at full brightness

Power Supply

P10 Outdoor LED Display Power Supply Options

Power supplies are the component most likely to clamp a whole wall to black, and the cheapest to get right. Excel LED fits P10 walls with three factory-verified brands — Mean Well, G-Energy and Chuanglian (confirmed per LEGIDATECH P10 series) — with the units matched to the module load and the site’s voltage:

  • Mean Well — the reference brand in LED power; factory-fit on the premium configurations, wide input range and full protection circuitry.
  • G-Energy — factory-fit on standard configurations; solid efficiency and protection, the volume choice for fixed billboards at a sane cost.
  • Chuanglian — China’s large-brand industrial power, same voltage-protection architecture, factory-fit for energy-tender projects.
Input Selected
Voltage AC 100–240 V, 50/60 Hz — one AC input, auto range (confirmed)
Working temperature −30 °C to +70 °C — the units run with this margin so summer midday doesn’t trip the thermal cutoff (typical, per LEGIDATECH P10 series)
Protection Over-current, over-voltage, short-circuit and surge protection; matching external surge arresters are included for high-lightning regions
Power budget B: 800/300 W/m² · A960: ≤550/≤186 W/m² · OK: 650 W max / 250 W avg per cabinet (confirmed per series)
Energy saving path Common-cathode architecture (A960, A1000) — cuts power draw ~25% against conventional layouts; also the A960 energy-saving series page shows the ROI math for a 10,000-nit high-power site

Buying note: a “high-quality power supply” promise is worth nothing without the brand and model on the BOM. Ask for the power list in your quotation — we send it with the full electrical drawing.

Control System

P10 LED Display Control System and Receiving Card

The control chain runs brand → sending card → receiving card → panels, and P10 walls accept the major outdoor control brands. From the factory, the line is compatible with all four: NovaStar, Huidu, Linsn and Colorlight (confirmed on the OK series page) — the receiving cards are dimensioned per cabinet, and a single receiving card drives one 960×960 cabinet (normal loading, per configuration).

NovaStar receiving card for P10 outdoor LED display cabinet
Huidu 4K receiving card for P10 outdoor LED display
  • NovaStar — the most common choice on DOOH walls; tight ecosystem of processors and software, strongest remote-diagnostics story.
  • Huidu — 4K-capable receiving cards with a simple video-player setup; the favorite for single-screen and standalone ad sites.
  • Linsn — solid mapping for large city-scale led walls and centralized control rooms.
  • Colorlight — matched when your main site already runs Colorlight, since one brand across the site means one operator’s software.

For media players and sensors the A1000 platform adds the industry option of running content locally with NOVA sensors; on the P10 line, remote brightness and temperature are set through the sending card of the brand you pick. If you are comparing control brands head to head, our LED control system guide covers the architecture; the practical rule: the best brand is the one your team already operates. We recommend the full set of receiving cards and the processor with your quotation.

Core Advantages

Why P10 Outdoor LED Screen Walls Hold Their Value: Brightness, Sealing and Service

The pitch, the cabinet and the surface work together; the short list of what a P10 wall actually buys you:

6,500

Daylight Legibility

6,000–6,500 nits standard, 10,000-nit option — a picture the sun cannot wash out.

IP65

Rain & Dust Sealing

IP65 on OK/B, IP66 on A960; conformal-coated boards and sealed connectors.

3,840

Camera-Ready Refresh

3,840 Hz class (7,680 Hz on A960) — no scan lines when the screen is filmed, streamed or shot from a car.

1/2

Outdoor Scan Economy

1/2-scan on A960 with common-cathode architecture; the standard module scan config is set per project.

Flat

Flatness That Stays

Die-cast consistency and hard-connection structure keep a large wall flat through thermal cycles.

F+R

Front- or Rear-Service

Both service modes on B/A960; front T-wrench on OK — pick at design, not at first repair.

Specifications

P10 Outdoor LED Display Technical Specifications

Parameter P10 Outdoor LED Display
Pixel Pitch 10 mm (confirmed)
Pixel Density 10,000 pixels/m² (confirmed)
Module Size 320×160 mm (standard) · 480×320 mm (A960) (confirmed)
Module Resolution 32×16 px (512) · 48×32 px (1,536) (confirmed)
Cabinet Size 960×960 mm — 77 mm OK / 88 mm A960 depth (confirmed)
Cabinet Resolution 96×96 px (confirmed)
Cabinet Material Aluminum profile (OK) · Magnesium alloy (B) · Die-cast aluminum (A960) (confirmed)
Cabinet Weight 25–28 kg (confirmed)
LED Lamp SMD 3535 (standard, confirmed) · SMD 2727 Jingtai (A960, confirmed) · DIP three-in-one option (typical)
Scan Mode Standard 320×160 module: 24/48 IC tiers (confirmed, factory list) · A960: 1/2 scan (confirmed)
Brightness 6,000 / 6,500 / ≥6,500 nits per series; 10,000-nits option (confirmed per series)
Refresh Rate 3,840 Hz (OK, A960) · 1,920–3,840 Hz (B) · 7,680 Hz option (confirmed)
Gray Scale 65,536 levels (confirmed, OK series)
Viewing Angle 140°/140° (OK) · 140°/120° (A960) (confirmed)
Color Temperature 6,500–9,000 K optional (A960, confirmed); standard 6,500–7,500 K (typical)
Protection IP65 (OK, B) / IP66 (A960) (confirmed)
Power Consumption B 800/300 W/m² · A960 ≤550/≤186 W/m² · OK 250 avg/650 max W per cabinet (confirmed per series)
Working Voltage AC 100–240 V, 50/60 Hz (confirmed)
Working Temperature −30 °C to +70 °C (typical)
Humidity 10–90% RH, no condensation (typical)
Lifetime ≥100,000 hours (typical, rated conditions)
Maintenance Front / rear / front & rear per series (confirmed)
Warranty 2-year standard site warranty, parts & workmanship; extended terms available
Need the full datasheet? Request it with your quotation and we send the BOM-level PDF for your configuration — module spec, IC and lamp models, power list, cabinet drawing and control design.

Pixel Pitch Guide

P10 Outdoor LED Display: Viewing Distance and Resolution Math

Resolution follows one formula: Resolution = Screen Width ÷ Pixel Pitch × Screen Height ÷ Pixel Pitch. At 10 mm pitch, a 9.6 × 5.76 m billboard resolves to 960 × 576 pixels — built from 60 cabinets (10×6) and 1,080 modules.

Worked examples (Illustrative):

• 9.6 × 5.76 m billboard → 9.6/0.01 = 960 px × 5.76/0.01 = 576 px → 60 cabinets (10×6), 1,080 modules

• 2.88 × 1.92 m pole sign → 288 × 192 px → 6 cabinets (3×2), 108 modules — the P10 minimum practical size

• 11.52 × 7.68 m facade → 1,152 × 768 px → 96 cabinets (12×8), 1,728 modules

Viewing distance rules for P10: minimum ≈ 10 m (pitch in mm × 1,000 — closer than that, pixels read as a grid), sweet spot 15–60 m for commercial readability, and it stays crisp at 100 m+ for headlines. Power consumption follows the same density logic: the P10 wall carries 10,000 px/m² against 15,625 on P8, so a site that can use P10 spends 36% fewer pixels on the same area — the reason highway and facade tenders settle at 10 mm.

For a full walkthrough of screen sizing see our LED screen size and dimensions guide, and our how to choose an outdoor LED display page for the pitch-choice logic.

Maintenance

P10 Outdoor LED Display: Front Maintenance vs Rear Maintenance

Service mode Front maintenance Rear maintenance Front & rear
Access route Modules pull from the face Modules + PSU + cards from behind Both, choose per site
Site requirement No corridor — facade, rooftop, flush mount Service walkway, ladder, or gantry Corridor optional
Speed per module swap Minutes with T-wrench Minutes with rear door Either method
Best used at Billboard-only fascia, building walls, mobile ad points Stadium perimeter, pole signs, highway gantries DOOH networks mixed

The engineering rule: front access is decided by the building, rear access by the operations plan. If the screen hugs a facade with the structure right behind the cabinet block, only front service works, and the OK T-wrench or B/A960 front access pays for itself at the first swap. If the site already has a walkway — stadium rings, gantry-mounted billboards — rear access keeps the modules cheaper and makes a service visit a two-person job instead of a crane job. It is one of the few decisions that is essentially unchangeable after installation, so specify it at tender stage. Full comparison in our front vs rear service guide.

Manufacturing

How a P10 Outdoor LED Display Is Manufactured

Thirteen steps run between the bare board and the crate. The ones in bold are where outdoor P10 quality is actually decided — every step below runs on the Excel LED factory line:

  1. PCB fabrication / SMT — board spec and component placement, with lamp and IC parts loaded from the confirmed BOM.
  2. Component reflow and first-pass optical inspection.
  3. Conformal coating (三防漆) — the three-proof lacquer layer applied over the populated board; this is the moisture barrier that separates a durable outdoor module from a quick failure.
  4. LED module assembly — lamps seated into the mask pockets, board aligned to the module frame.
  5. Mask installation — the black-oil-finished mask fitted and stress-checked; mask geometry verified against the viewing cone.
  6. Module sealing — connector zone sealed, edges bonded (waterproofing step).
  7. Cabinet assembly — frame build-up, splicing surfaces and locking plates checked flat.
  8. Wiring and power routing — cable ducts, rated connectors, ground path to the cabinet frame.
  9. Power supply and receiving card installation, with the surge-arrester connections made.
  10. Module luminance calibration — brightness and color matched across the wall to one datum.
  11. Aging test — 72 hours continuous burn at rated load; thermal-cycle and humidity checks pull out weak solder joints before packing.
  12. Final inspection — dead-lamp scan, splicing check, IP sealing sample, packing list against the BOM.
  13. Packaging — modules in cartons with EPE pockets, cabinets on wooden skids or flight cases, wiring diagram and spare parts in the crate.

LED display factory SMT production line assembling P10 outdoor module boards

Factory access for integrators is available — we run a factory video tour and an on-site visit program. For project evidence, the LED display case gallery and the LED display knowledge hub show installed walls and the engineering behind them.

Indoor vs Outdoor

P10 Outdoor LED Display vs Indoor P10 LED Display

P10 is possible indoors too — a 10 mm pitch, lower weatherproofing and fireproofing requirements, and significantly lower cost because no IP65 build, no high-brightness lamps and no conformal-coated boards are needed. Indoor P10 appears in very large-perception venues: big sports halls, clubs and exhibition spaces with 6 m+ viewing. Where the user context shifts from “how does it survive weather” to “is the indoor picture sharp enough”, the honest answer is: for indoor walls, go finer on the pitch before you go coarser on the cabinet.

Indoor LED display technology splits into three packaging tiers, and the right choice follows the environment — our SMD vs GOB indoor LED display comparison covers the detail:

Technology Surface protection Contrast Pitch range Maintenance Best for
SMD Standard High P1.2+ / P10 indoor Front / rear General indoor
GOB Enhanced — epoxy coat over the lamps High Fine pitch Front / rear High-touch, high-risk environments — exhibition, rental, retail
COB Chip-level packaging Very high Fine / ultra-fine pitch Front Control room, conference, premium display

On the naming side, COB indoor models carry the packaging in the product name — “COB P1.2 LED Display” instead of “P1.2 LED Display” — because the package is the first decision the integrator makes. Our COB LED screen for indoor hub lists those models by pitch, and the indoor LED screen collection covers the SMD lines.

Practical split: outdoor 10 mm = high brightness + IP65 + coating + screws. Indoor = privacy of the environment decides the pitch. P5 and above indoors, SMD is normally enough; fine-pitch rooms profit from GOB where touch risk exists, and COB where the client wants the highest contrast and a 16-bit-class picture.

Use Scenarios

Where a P10 Outdoor LED Display Earns Its Money: Billboard, Facade and Stadium Sites

P10 fits where distance is the first design input — the pitch is matched to the viewing cone, the brightness to the sun, and the maintenance mode to the structure:

Application Why P10 fits
Highway & roadside billboard 15–100 m viewing distance, 6,000–6,500 nits holds against the sun, 10,000 px/m² keeps the pixel budget sane at 100 m²
Building facade 400–1,000 m² grids, 960 mm module grid splices to the cladding grid, front access saves the facade treatment
Stadium scoreboard & show screens Far-bowl viewing, high refresh (7,680 Hz option on A960) for live camera work, IP66 for open-air stands
Public square & transit plaza Wide viewing field, dual maintenance on B/A960 for short night windows, conformal-coated boards survive urban weather
Pavement & pole signage Budget-first small-format P10 — 2.88 × 1.92 m pole tops, steel or aluminum cabinets, rear access through the ladder
DOOH networks Standard 960 grid across cities means one spare-parts kit, one BOM, one maintenance procedure

P10 outdoor LED display stadium scoreboard for live sports viewing

Real projects — P10 and P10-family. Outdoor billboard P10 to Uganda (see the case photo below), an outdoor P10 project in the USA and a P10 LED sign to Zambia — the full gallery is on the LED display case page.
Module Sizes

Which Module Sizes Does a P10 Outdoor LED Display Use?

This pitch is quoted in 3 module formats in our production list. All of them produce the same 10,000 px/m² wall — they differ in board size, how many fit a cabinet, drive scheme and serviceability. Pixel figures below are exact arithmetic from the pitch (1,000 ÷ 10 mm = 100.0 px per metre), cross-checked against the factory module list.

Module size Resolution & dots Per cabinet Boards per m² LED & drive Notes & service
320×160 mm 32×16 px
512 dots
18 19.53 SMD 3535 · 24 or 48 ICs Front & rear — front access on B/A960 builds, swap in minutes
480×320 mm 48×32 px
1,536 dots
6 6.51 SMD 2727 Jingtai · 1/2 scan Front & rear
160×160 mm (/ 320×160 board)
typical, on request
16×16 px
256 dots
— 39.06 three-in-one DIP lamps Rear — classic DIP service access
The insight worth keeping: Module size never changes the picture at this pitch — it changes the bill of materials. Density, cabinet resolution and viewing distance stay identical across all 3 formats; board count, connector count, assembly labour, spare-part granularity and price move.
Cabinet Sizes

Which Cabinet Sizes Does a P10 Outdoor LED Display Ship In?

960×960×77 (W×H×depth) mm is the standard carrier for this pitch: 18 × 320×160 mm, resolving to 96×96 — 9,216 px. Every further format below is built for a specific layout problem rather than for a better picture.

Cabinet (W×H) Modules inside Resolution Weight / body Service access
960×960×77 (W×H×depth) mm 18 × 320×160 mm 96×96
9,216 px
28 kg · Aluminum profile frame Front — T-wrench tool-free; rear on request
960×960 (depth not stated) mm 18 × 320×160 mm 96×96
9,216 px
28 kg · Magnesium alloy, two integrated extraction fans Front & rear — dual access
960×960×88 (W×H×depth) mm 6 × 480×320 mm 96×96
9,216 px
25 kg · Die-cast aluminum, hard-connection CNC structure Front & rear

Why 960 mm became the outdoor standard grid

Three practical reasons, and they all save money later. Structure arithmetic: a 960 mm unit gives clean multiples for billboard frames and facade cladding. Ratio: 4:3 and 16:9 screen shapes land close to whole-cabinet counts, so you buy few cut cabinets. Interchangeability: replacement cabinets in five years still bolt onto the same holes.

Industry-standard cabinet grids for this module size (on request)

These grids are the ones the industry builds around this module size, and each one is arithmetic-clean — the modules tile with no cut strip. They are quoted on request rather than stocked, and the pixel figures are pure arithmetic from the pitch.

Cabinet (W×H) Modules inside Resolution & pixels Grid status
1280×960 mm
on request
4 × 6 × 320×160 mm modules (4 × 6) 128×96
12,288 px
standard outdoor grid
640×640 mm
on request
2 × 4 × 320×160 mm modules (2 × 4) 64×64
4,096 px
standard outdoor grid
The arithmetic you can do in your head Wall size = cabinet count × 0.96 m wide × 0.96 m high. Pixels = cabinet count × the cabinet resolution above. Weight = cabinets × cabinet weight. Send us the wall dimensions and we return this as a drawing with the cabinet count already worked out.

Which cabinet form should you pick?

  • Standard roadside or stadium facade → the 960×960 cabinet: the price and lead-time sweet spot, and the format spares are stocked in.
  • Long highway span lifted by crane once → wider cabinets (1280×960 class): fewer crane picks and fewer splices for the same picture.
  • Retrofit onto existing steel, or a narrow pillar face → the compact 640×640 class: lighter per piece and easier to move by hand or lift.
  • Coastal or corrosive site → the cabinet body matters more than the size: die-cast aluminium with a high IP rating and conformal-coated boards.
  • Curved or creative shape → a fixed outdoor cabinet grid is the wrong tool; use a bendable-board pitch instead.
Control Systems

Which Control Systems Work With a P10 Outdoor LED Display?

A P10 Outdoor LED Display is electrically ordinary: standard HUB75 module interface, conventional outdoor scan, low-voltage module rails. That is why it accepts essentially every mainstream control ecosystem — the real decision is not “which system is compatible” but which family your operators already run, because sending cards and receiving cards must come from the same family.

The signal chain, end to end

  • 1. Video source — media player, PC, camera or streaming decoder.
  • 2. Video processor / sending card — scales, switches and packetises: HDMI / DVI / SDI in, gigabit Ethernet out.
  • 3. Transport — Cat6 for normal runs, fibre where the distance or the lightning risk demands it.
  • 4. Receiving card — one receiving card per cabinet is the standard loading (9,216 px per cabinet).
  • 5. Modules — 18 × 320×160 mm per cabinet, daisy-chained POWER IN/OUT and SIGNAL IN/OUT.
Ecosystem Typical hardware Best for
NovaStar
page-confirmed
MRV336 receiving card · MCTRL660 controller · MCTRL4K 4K sender Large fixed walls that need remote diagnostics and per-pixel calibration
Colorlight
page-confirmed
i9+ receiving card · X16 video processor Billboard and signage budgets; sites already running Colorlight
Huidu
page-confirmed
HD-C16C async control card · VP620 video processor Single-screen ad sites scheduled from a phone, no PC on site
Linsn
page-confirmed
DH7512 receiving card City-scale walls and centralised control rooms
Mooncell
budget sending, 2-in-1 processing and player hardware we stock
MVB20E-G 2-in-1 processor Cost-controlled fixed installs and second-source spares
VDWALL
video processing line we stock
LVP605 video processor Stadium, broadcast and multi-source control rooms
RGBlink
switcher-processor hybrids we stock
X2 modular video wall processor Live production and event broadcast workflows

How many receiving cards does a P10 Outdoor LED Display need?

Two limits decide the card count, and the smaller one wins. Pixel capacity: one 960×960×77 (W×H×depth) cabinet carries 9,216 px, and a mid-range card such as the MRV336 loads 256×256 = 65,536 px at 60 Hz — that is 7 cabinets per card. Port loading: the same card has 12 HUB75 outputs, and a cabinet here needs 6 / 18 module feeds, so the ports allow 1 cabinet. The binding limit is 1 cabinet per card (the port count).

Practical rule for quoting. Plan one receiving card per cabinet at this resolution, then confirm the loading figures with the platform you choose.
  • Redundancy — on revenue-critical walls add a second sending card in hot standby; a failed cabinet still does not take the wall down.
  • Remote management — NovaStar and Colorlight sending platforms report cabinet temperature and voltage and support scheduled brightness by time of day.
  • The one rule that saves the most money — sending card and receiving cards from the same family. Mixing families is the most common commissioning failure we get called about.
  • Documentation — the port map, receiving-card loading sheet and configuration file ship with every order.

The architecture of each role — sender, processor, receiving card, async player — is compared in our LED control system collection.

Case Evidence

Successful P10 Outdoor LED Display Projects

P10 outdoor LED billboard cabinets prepared for shipment to Uganda

Outdoor P10 LED billboard — Uganda

Fixed installation for an outdoor advertising billboard: 960×960 mm OK-platform cabinets, IP65, 96×96 px per panel, aged and calibrated before shipment.

P10 outdoor LED display cabinets assembled and checked in the factory for the USA project

Outdoor P10 LED display project — USA

Cabinet-level assembly and pre-shipment QA for a P10 wall bound for the USA: the build is checked on the factory floor, wired and powered before packing, with the local temperature range specified at the design stage.

P10 LED sign — Zambia

Building-facade advertising: a 5.76 × 2.88 m P10 screen (3 panels) mounted over the storefront — a case of the 960 mm grid matching a budget directly. Additional P5-class and rental projects are on the LED display case gallery.

Deep Dive

P10 Outdoor LED Display: The Complete 5W1H Buying Guide

Everything above, assembled into one long-form reading path — What it is, Why it exists, Who buys it, Where it lands, When it is the right call, and How to buy it without overpaying.

What is a P10 outdoor LED display, exactly?

A P10 outdoor LED display is a 10 mm pixel-pitch, high-brightness LED wall for exterior installations. “P10” means the center-to-center distance between two adjacent pixels is 10 mm; the display holds 10,000 pixels per square meter, 512 points per 320×160 module, and 96×96 pixels per 960×960 cabinet. It is a complete electronic appliance, not a component — module electronics, casing, power, control and thermal design engineered as one BOM. Its picture is engineered for sunlight: 6,000–10,000 nits of brightness, an IP65/IP66 build, a black-oil-finished mask and conformal-coated boards, so the cheapest cost per square meter in the full outdoor family still survives the weather for a decade of operational life.

Why choose a 10 mm pixel pitch?

Because the distance decides the pitch, not the other way around. At 10 mm, the minimum comfortable viewing distance is roughly 10 m: if your audience is 15 m or more away — a highway lane, a plaza, the middle of a stadium — P10 looks as sharp as a finer pitch costs less. It buys that sharpness for about 36% fewer pixels than P8 and ~56% fewer than P6.667 on the same area, which lowers both the component cost and the power draw. The A960 common-cathode platform then cuts the draw another ~25% with no sacrifice in brightness. There are, however, honest limits: under 10 m, pixel structure becomes visible; use the pitch ladder from P8 down for closer commercial sites.

Who should buy a P10 outdoor LED display?

  • LED integrators and DOOH system suppliers — the 960×960 grid keeps one spare parts set across projects.
  • Advertising companies and media owners — billboard and facade specs where cost per square meter is the tender.
  • Stadium and sports venue contractors — scoreboard screens at 100 m+ viewing with camera-clean refresh.
  • Property developers and sign builders — facade media walls and building signage with front access.
  • Transport and public-signage suppliers — ports, parking, plaza screens run 24/7 on the energy-efficient platform.

Where do P10 LED displays work best?

Wherever the audience stands farther back than the pitch’s minimum — the commercial center, the highway side, the stadium bowl, the public square. The three environments to avoid are the ones with a close audience: shopfronts at 3 m, transit stops with 1 m seats, or an entrance wall inside a corridor. Those need the indoor family. And for any site where newspapers or planning restrict brightness, the 10,000-nit option is the wrong answer too; ask for the ambient-light profile and we size the brightness to the actual site.

When does a P10 LED display make sense?

Three conditions for the go-decision: (1) the viewing distance clears ~10–15 m and most viewers are outside it; (2) the budget is size-driven — a wide-area wall at P10 covers the same area as its P6 cousin for tens of percent less; (3) the weather is real — rainfall, high humidity or coastal salt, all of which the IP65/66 and coated-board P10 build handles. If a site is fully finished and needs a wall that is truly private-facing (a showroom, a press room), skip to indoor. If the competition will film the wall repeatedly, remember the 3,840 Hz floor — and 7,680 Hz on the A960 platform.

How to buy a P10 outdoor LED display (and what the price depends on)

The eight factors that move a P10 price:

1. Lamp package and brand — SMD 3535/2727 (Jingtai confirmed on A960), DIP alternative.
2. Driver IC count and scan rate in the module BOM.
3. Cabinet material — aluminum profile vs magnesium vs die-cast, and its process tolerance.
4. Brightness class — 6,000, 6,500 or 10,000 nits.
5. Refresh — 1,920 vs 3,840 vs 7,680 Hz.
6. Control brand — NovaStar, Huidu, Linsn or Colorlight, plus processor and receiving-card count.
7. Maintenance mode — front access hardware adds cost.
8. Quantity, structure scope (electric, mounting), and shipping region.

The order matters: give us the site’s screen size (W×H), viewing distance, sun and weather profile, and maintenance preference, and we return the configuration-matched quotation with cabinet/module counts, the BOM, the power and control design, and the freight terms. The full price logic for outdoor screens is broken down on our outdoor LED screen price guide; when you are ready to short-list suppliers, check the leading brands and the 100+ page LED display knowledge hub for background.

FAQ

Frequently Asked Questions About P10 Outdoor LED Displays

Q1 What does P10 mean on an LED display?

P10 means the pixel pitch is 10 mm — the center-to-center distance between neighboring pixels. At this pitch the display carries 10,000 pixels per square meter and looks sharp from about 10 m and beyond, which makes it the cost-effective choice for outdoor billboards, facades and stadium screens.

Q2 What is the best viewing distance for a P10 outdoor LED display?

About 10 m and beyond; the practical sweet spot for reading content is 15–60 m, and headline impact holds past 100 m. The rule of thumb is pitch in millimeters × 1,000: 10 mm → roughly 10 m minimum. Under that, pixel structure becomes visible and a finer pitch like P8 should be used.

Q3 What cabinet sizes are available for P10?

All three P10 platforms share the 960×960 mm standard grid: OK 960×960×77 mm aluminum (28 kg), B 960×960 mm magnesium (28 kg), and A960 960×960×88 mm die-cast aluminum (25 kg). Each carries 96×96 pixels; custom sizes are produced on request for non-standard layouts.

Q4 Which P10 series does Excel LED offer?

Three: the OK series (aluminum 960×960 cabinet, 6,500 nits, 3,840 Hz, IP65, front T-wrench service), the B series (magnesium cabinet, 6,000 nits, front & rear access, universal 320×160 mm module ecosystem) and the A960 series (die-cast, ≥6,500 nits, IP66, common-cathode energy saving, 1/2 scan).

Q5 How many pixels on a 320×160 P10 module?

512 pixels — 32×16 resolution. The A960 platform’s 480×320 mm module carries 1,536 pixels at 48×32. A full 960×960 mm P10 cabinet therefore resolves to 96×96 pixels.

Q6 What is the difference between DIP and SMD P10 modules?

DIP lamps are tall through-hole bodies with typically stronger brightness and a narrower viewing angle — best for long-distance billboards. SMD lamps sit on the board through a smaller surface, generally wider in viewing angle (140°/140° class) and now equal in brightness — the default on the OK/B/A960 platforms at 3535 and 2727 sizes.

Q7 Is a P10 module PCB really waterproofed?

Yes, by process, not by a single seal: outdoor P10 modules use a conformal-coated (three-proof lacquer) PCB with 1.2 mm stainless-steel screws, a sealed connector zone and a black spray-oil mask, inside an IP65–IP66 cabinet. The conformal coating is what stops the humidity-caused corrosion cascade on long-term outdoor walls.

Q8 What brightness does a P10 outdoor LED screen need?

6,000–6,500 nits is the standard range — B series at 6,000, OK at 6,500 and A960 at ≥6,500 nits. Sites facing direct morning sun or needing maximum contrast can take the 10,000-nits option on the A960 platform. Indoor sites use a fraction of this, around 800–1,000 nits (typical).

Q9 What scan mode does the P10 module use?

The confirmed A960 P10 module runs 1/2 scan with 48×32 pixels and SMD 2727 lamps. The standard 320×160 SMD module is configured per project — the scan and driver IC are matched to the brightness and budget you specify, and the exact value appears on your BOM.

Q10 Which control systems work with a P10 wall?

All four major outdoor brands: NovaStar, Huidu, Linsn and Colorlight — confirmed compatible on the OK series page. The best pick is the brand your team already operates: one brand across a network means one software, one spare-card philosophy and one remote-diagnostics setup. Receiving-card counts are calculated against the scan and loading per cabinet.

Q11 How much does a P10 outdoor LED display cost?

Price is configuration-first: lamp package and brand, driver ICs and scan, cabinet material, brightness (6,000 vs 10,000 nits), refresh rate, control brand, maintenance mode and order size. Send your screen size, viewing distance and site conditions and you get a BOM-level quotation — cabinet/module counts, power and control design — not a mystery price.

Q12 What warranty comes with a P10 outdoor LED display?

A standard 2-year site warranty on parts and workmanship, covering lamp failures, driver ICs and power supplies under normal use. Warranty support includes remote diagnosis and spare-part dispatch; extended terms can be arranged for large projects. All P10 walls ship with the 72-hour aging and calibration record.

Get Factory-Direct Pricing for Your P10 Outdoor LED Display

Tell us five things and we return a comparable, BOM-level quotation — 1. Screen size (W×H) · 2. Viewing distance · 3. Sun & weather profile · 4. Brightness class · 5. Maintenance preference. You get the cabinet/module count, the series recommendation (OK, B or A960), the power and control design, and shipping terms — not a mystery price.

Get My P10 Display Quote →

P10 Outdoor LED Display — OK, B and A960 Series, IP65/66 Front & Rear Maintenance

The P10 outdoor LED display is the volume pitch for large-format outdoor work: 10,000 px/m² across three platforms — OK (aluminum, 6,500 nits, 3,840 Hz), B (magnesium, 6,000 nits, universal 320×160 modules) and A960 (die-cast, IP66, common-cathode, ≤186 W/m²) — with conformal-coated PCBs, black spray-oil masks, 1.2 mm stainless screws, 2-year warranty and 72-hour factory aging. Match the platform to the site and the maintenance mode to the building, and P10 holds its sharpness for a decade of outdoor life at the lowest cost per square meter in the line.

Related reading: Outdoor P8 LED display · Outdoor P6 · Outdoor P4 · Outdoor LED screen price guide · Front vs rear service guide · LED control system guide · LED display case gallery · LED display knowledge hub

Scroll to Top

Contact Us Now!

Thank You for Your Inquiry!

 Our LED display expert will contact you within 12 hours.

You can also contact us directly: +86 18569492693 ;excelledscreens@gmail.com