Indoor commercial display solutions

Indoor Commercial LED Displays for Retail, Malls and Brand Spaces

An indoor commercial LED display is a modular video wall built for retail stores, shopping malls, showrooms and corporate lobbies. This page covers the routes Excel LED supplies, the site decisions that change the specification, and the content and service questions a commercial buyer needs to settle before approving a quotation. If you are still comparing display categories, start with the indoor LED screen collection.

Retail storesShopping mallsShowroomsLobbies and hotelsP1.2–P3.9 routesFront service
Mall atrium indoor commercial LED display with shoppers
Mall atrium display in active use.

01 — Definition and scope

What Is an Indoor Commercial LED Display and When Does It Fit?

Short answer: An indoor commercial LED display is a fixed or semi-fixed LED video wall specified for a business interior, not a rental stage screen. The right specification depends on the nearest viewer, the content schedule, the mounting depth and who will service the wall. For retail and mall projects, confirm the target wall size and viewing distance first, then choose a cabinet family and pixel pitch. Use this page to compare commercial routes; confirm the final cabinet layout and quotation with an engineer.

An indoor commercial LED display is a modular LED video wall specified for a business interior where the screen supports sales, brand presentation or visitor information. It is built from cabinets and modules, mounted on a wall, recess, frame or floor support, and driven by a sending controller, processor or media player. Unlike a rental stage wall, the display stays in place and has to work with the room’s light, daily content schedule and service access.

The commercial brief changes the order of decisions. A product page starts with a cabinet or pixel pitch; a commercial project starts with the wall, the viewer and the operating routine. Those three inputs decide whether the right answer is a lightweight Ehonor wall, a 16:9 CPS wall, a slim PS wall or a fine-pitch Uni wall.

Four decisions that shape the specification

  1. The wall size comes before the product series. A 4.8 × 2.7 m opening and a 6 × 3 m opening can use the same series but not the same cabinet count, pixel matrix or control load.
  2. The nearest viewer sets the pitch band. A showroom visitor standing 1.5 m from the wall sees pixel structure that a shopper 8 m away in a mall atrium will never notice.
  3. The content schedule sets the control route. A single store with a USB player and a multi-site chain with scheduled campaigns need different hardware, software and permissions.
  4. The service route sets the cabinet and mounting detail. If the wall has no rear access, front-service modules, power supplies and receiving cards have to be confirmed before the frame is designed.
Where this page sits: use the indoor LED screen collection for the full category. Use indoor fixed LED display for permanent mounting detail, indoor high resolution LED display for native 4K planning, fine pitch LED display for P1.5 and below, and COB LED screen for indoor for flip-chip COB options.
Commercial question Why it changes the specification What to send
Where will people stand? Sets the pitch band, brightness and viewing angle Nearest and farthest viewing distance; a site photo
What will run on the screen? Sets resolution, refresh, player and scheduling route Video, stills, menus, price text, live input or dashboards
How does the wall meet the room? Sets cabinet depth, frame, recess and ventilation Wall drawing, opening depth, access route and finish
Who will operate it? Sets software, permissions and training Store staff, marketing team, agency or AV integrator

02 — Applications

Which Indoor Commercial LED Display Solutions Fit Retail, Malls, Showrooms and Lobbies?

The same LED technology behaves differently in a shop window, a mall atrium, a brand showroom and a hotel lobby. The differences are practical: who controls the content, how close people stand, how much daylight reaches the screen, and how a technician reaches the cabinet after opening day. The four briefs below cover most commercial inquiries. Use them to shortlist a route, then confirm the wall with a drawing.

Indoor commercial LED display being commissioned in a retail store
Retail installation during commissioning.

Retail stores

Retail Stores: An Indoor Commercial LED Display for Window and Interior Campaigns

A window-facing screen competes with daylight; an interior wall works with focused store lighting. Check measured brightness at the glass, not just the datasheet. For a 2–4 m viewing distance, P1.5–P2.5 is the common band. Confirm who updates weekly offers and whether the player can run a schedule without staff intervention. Start with the retail store LED display solution.

Portrait indoor commercial LED display suspended in a shopping mall atrium
Portrait mall display running a fashion campaign.

Shopping malls

Shopping Malls: An Indoor Commercial LED Display for Atrium and Feature Walls

Mall screens are viewed from 4–10 m and often run advertising or sponsor content on a schedule. Portrait columns, ribbon screens and large atrium walls use different cabinet grids. The structural hang, service path and advertising scheduling matter as much as pitch. Review the shopping mall LED display solution before fixing the format.

Curved indoor commercial LED display behind a reception desk in a brand showroom
Curved showroom wall behind a reception desk.

Showrooms

Showrooms: An Indoor Commercial LED Display for Close-View Brand Content

A brand experience center is a close-view environment. Visitors read product names, watch detail footage and may stand within 1.5 m of the wall. P1.2–P2.0, good low-brightness grayscale and a calibrated color profile matter more than maximum nits. Curved and corner layouts are possible, but the cabinet grid and seam plan have to be drawn first. Compare high-resolution indoor options.

Indoor commercial LED display in a hotel lobby seating area
Lobby display in a hotel seating area.

Lobbies and hotels

Lobbies and Hotel Reception: An Indoor Commercial LED Display for Arrival Spaces

A lobby screen is part of the interior. It usually runs at lower brightness, changes less often and needs quiet operation and a clean cable route. P1.5–P2.5 covers most reception walls; a slim PS cabinet helps where the wall depth is tight. Confirm who can change the welcome message and how the screen behaves outside business hours. See the hotel LED display solution.

Commercial setting Nearest viewer Typical pitch band Content cycle Service note
Retail store, interior wall 2–4 m P1.5–P2.5 Daily or weekly offers Front service preferred; confirm player access
Retail window 1–3 m P1.5–P2.0 Campaign and seasonal Check brightness at the glass; heat and glare
Mall atrium or column 4–10 m P2.5–P4 Scheduled advertising Hanging structure, service platform, content scheduling
Showroom 1.5–3 m P1.2–P2.0 Product stories, demo loops Calibration, low-brightness performance, touch risk
Lobby or hotel reception 2–5 m P1.5–P2.5 Welcome, events, brand film Quiet operation, discreet cable route, staff permissions

How Do Mall and Retail Commercial Indoor LED Display Installations Look in Use?

Two short project clips show the scale and viewing conditions that a drawing cannot. The first is a 7.36 × 1.44 m Ehonor P2.5 wall in a shopping mall; the second is an indoor shopping-center installation from the Excel LED channel. Use them to judge content size, viewer distance and the amount of surrounding light, not as a substitute for a site survey.

Videos: Legidatech LED screen (Ehonor P2.5 mall project) and EXCEL LED DISPLAY (shopping-center installation). Both are embeddable public videos.

Also fits: restaurants and cafés, museums and exhibition stands, automotive showrooms, supermarkets and grocery retail, and transport retail. The pitch and control route change, but the sequence is the same: wall, viewer, content, service.

Request a Retail or Mall Configuration

03 — Series routes

How Do You Compare Indoor Commercial LED Display Series for a Project?

Four Excel LED cabinet families cover most commercial briefs. The comparison below is written for a commercial buyer, so it starts with the wall and the operating routine, not with a full datasheet. Confirm the final pitch, cabinet count and control load on a drawing before comparing prices.

Ehonor 480 by 320 mm indoor LED cabinet with front-service modules
Ehonor 480 × 320 mm front-service cabinet.

Value and light weight

Ehonor: An Indoor Commercial LED Display Cabinet for Budget-Sensitive Retail

480 × 320 × 70 mm; 2.7–3 kg. P1.25–P3.076. Front-service magnetic modules. A light cabinet for retail interiors, meeting rooms and halls where the wall does not need a 16:9 native matrix. Portrait or horizontal orientation. View Ehonor series.

Request This Series

CPS 640 by 480 mm indoor LED cabinet with front-service modules
CPS 640 × 480 mm cabinet.

16:9 and control rooms

CPS: An Indoor Commercial LED Display Cabinet for 16:9 Media Walls

640 × 480 × 65 mm. P1.2–P3. 800 nits; 3,840/1,920 Hz. Front service; confirm whether power supplies and receiving cards are included in the front-service scope. A practical route for 16:9 retail media walls, conference rooms and control rooms. View CPS series.

Request This Series

PS 1,000 by 250 mm slim indoor LED cabinet
PS 1,000 × 250 mm slim cabinet.

Slim and recessed

PS: An Indoor Commercial LED Display Cabinet for Slim or Curved Walls

1,000 × 250 × 20.6 mm; 2.4–4.8 kg. P1.56–P3.91. Front service for modules, power supplies and receiving cards. 90° corners; IP43. A 20.6 mm cabinet helps in a shallow recess, but the total wall depth still includes the bracket, cables and ventilation. View PS series.

Request This Series

Uni 600 by 337.5 mm COB indoor LED cabinet
Uni 600 × 337.5 mm COB cabinet.

Fine pitch COB

Uni: An Indoor Commercial LED Display Cabinet for Close-View Brand Walls

600 × 337.5 × 39.75 mm; 4 kg. P0.625–P1.875. Flip-chip COB; 600 nits; 3,840–7,680 Hz. Front service; three-in-one power, card and HUB board. A route for showrooms, boardrooms and close-view retail where text and product detail are read at 1.5–3 m. View Uni series.

Request This Series

Series Cabinet Pitch band Best commercial fit Service Why shortlist
Ehonor 480 × 320 × 70 mm; 2.7–3 kg P1.25–P3.076 Retail interiors, meeting rooms, value walls Front-service modules and cabinet Light cabinet; low structural load
CPS 640 × 480 × 65 mm P1.2–P3 16:9 media walls, conference, control rooms Front service; confirm PSU/card scope 16:9 layouts; 800 nits
PS 1,000 × 250 × 20.6 mm; 2.4–4.8 kg P1.56–P3.91 Slim recess, columns, 90° corners Modules, PSU and cards from front 20.6 mm cabinet; IP43
Uni 600 × 337.5 × 39.75 mm; 4 kg P0.625–P1.875 Close-view showroom, boardroom, premium retail Front service; three-in-one board COB surface; fine pitch

If none of the four fits, check the CPS Pro Max COB series for a 640 × 480 COB wall, the Cni series for a 600 × 337.5 COB wall, or the All-in-One LED display for a meeting-room screen with an integrated cabinet. For the full COB range, use the COB LED screen for indoor collection.

Request a Series Comparison

  1. Cabinet size changes the wall grid. A 600 × 337.5 mm cabinet and a 1,000 × 250 mm cabinet rarely produce the same visible seams or the same native resolution on the same opening.
  2. Surface protection changes the service and touch risk. SMD, GOB and COB differ in impact resistance and cleaning; a reachable retail wall needs that decision early.
  3. Service access changes the mounting depth. Front service can remove the rear aisle, but the frame still needs a ventilation and cable zone.
  4. Control load changes the processor. The pixel count, not the screen area alone, decides whether a sending card, processor or media player is enough.

04 — Selection

How Should You Choose an Indoor Commercial LED Display for Your Content and Room?

Selection is a sequence of constraints. Start with the nearest viewer, then the content, then the wall geometry, then the service route. A larger pitch can be the correct choice in a mall atrium; a smaller pitch can be wasted in a lobby where nobody stands closer than 4 m. The tables below give a planning band, not a guarantee.

How Do You Match an Indoor Commercial LED Display to Viewing Distance?

Nearest viewer Typical pitch band Content that works Series to review
Up to 1.5 m P0.9–P1.25 Product detail, small text, close-up camera work Uni, CPS Pro Max
1.5–2.5 m P1.25–P1.56 Showroom loops, menus, presentations Uni, PS, Ehonor, CPS
2.5–4 m P1.56–P2.0 Retail campaigns, reception, brand films PS, Ehonor, CPS
4–6 m P2.0–P2.5 Mall feature walls, large retail interiors Ehonor, PS, CPS
6 m and above P2.5–P3.91 Atrium advertising, large halls, distance viewing Ehonor, PS

Use the indoor LED display pixel pitch guide for the full calculation, including text height and camera distance. The table above is a shortlist tool; the final pitch should be checked against the actual content and the closest standing position.

How Do You Confirm Native Resolution on an Indoor Commercial LED Display?

Native resolution is the physical pixel matrix of the wall, not the input format of the processor. A 4.80 × 2.70 m wall built from 600 × 337.5 mm Uni cabinets at P1.25 uses 8 × 8 = 64 cabinets. Each cabinet is 480 × 270 pixels, so the wall is 3,840 × 2,160 pixels: a native 4K matrix. If the same opening uses a larger pitch, the physical matrix drops even if the processor accepts a 4K signal.

Rule to apply: ask for the cabinet count, cabinet pixel matrix and final wall pixel matrix in writing. “4K input” and “native 4K” are different specifications. Use the indoor high resolution LED display guide for 4K and 8K layouts, and the 16:9 aspect ratio guide when the opening is not a clean 16:9.

How Do You Check Brightness and Surface Protection on an Indoor Commercial LED Display?

Ask for measured nits at 100%, 50% and 10%, not just a headline figure. A lobby wall that runs at 200–400 nits all day needs good low-brightness grayscale; a window-facing retail wall needs a brightness check under the actual glass and lighting. For reachable walls, compare SMD, GOB and COB surfaces and confirm how a damaged module is replaced. The COB vs SMD indoor LED display comparison covers the surface trade-offs.

For a close-view showroom: prioritize low-brightness grayscale, color calibration and P1.2–P1.56. Confirm the content is mastered at the wall’s native matrix.
For a mall atrium: prioritize structural access, service path and a pitch that reads at 4–10 m. A finer pitch adds cost without a visible gain at that distance.

Send Your Wall Dimensions

05 — Content operations

How Do You Manage Content on an Indoor Commercial LED Display Every Day?

Content management is a configuration decision, not a feature that appears automatically with the screen. The wall needs a source, a player or controller, a scheduling tool and a person who owns the campaign calendar. Confirm the route before the cabinet order, because the player, network and software affect the control hardware and the commissioning work.

Which Indoor Commercial LED Display Content Setup Fits One Store or a Chain?

Operating model Who it suits What is included What to confirm
Local player One store or venue; simple loop Media player, USB or local network upload, basic schedule Player model, file formats, software licence, who uploads
Networked single site One site with remote marketing control Player plus network; scheduled publishing from an office Firewall, network access, fallback playback, support contact
Multi-site chain Retail chain, mall group, hotel group Central CMS, compatible players, roles, logs, scheduled campaigns Offline behavior, permissions, local support, content approval
Agency-managed Brand team with an external agency CMS access, approval workflow, campaign templates Role scope, asset handover, reporting and SLA

A sending controller, a media player and a CMS are three different things. The controller drives the receiving cards and the pixel load; the player stores and plays content; the CMS schedules and distributes it. A project can use one, two or all three. Ask which item is standard, which is optional and which requires a subscription.

  1. Brief the content. Confirm the campaign length, text size, video frame rate and whether the screen must show live input or dashboards.
  2. Choose the player and software. Match the player to the pixel load, network and scheduling model; confirm the licence and update path.
  3. Build the schedule. Set campaign dates, dayparts, playlists and fallback content for network loss.
  4. Publish and check. Verify the content on the actual wall, including color, crop and text legibility at the nearest viewing position.
  5. Hand over. Train the operator, record the login and document who can change content and who can change the configuration.

Request a Content and Control Review

06 — Installation and service

How Is an Indoor Commercial LED Display Installed and Serviced?

The installation method should follow the wall, not the other way around. A solid wall, a shallow recess, a structural frame and a hanging position each change the bracket, the service route and the responsibility split. The screen is only one part of the delivery; the wall capacity, power distribution, cable routes and final finish also decide whether the project opens on time.

Which Commercial Indoor LED Display Installation Method Fits Your Wall?

Wall-mounted: a bracket or frame carries the cabinets on the finished wall. It is the simplest route when the wall is flat and can take the load. Recessed: the cabinets sit inside an opening, so the opening depth must include the cabinet, bracket, cables and ventilation. Suspended or floor-supported: a truss, ceiling frame or base carries the wall; this route needs a structural check and a service plan for high-level cabinets. For a custom shape, send the elevation and the nearest viewer position before the cabinet grid is fixed.

01 Wall or openingConfirm load capacity, flatness, finish and the allowed penetration points.
02 Bracket or frameSet the stand-off, adjustment range, cable zone and ventilation gap.
03 CabinetFix the cabinet grid, pitch, power and signal distribution. The cabinet depth is not the total wall depth.
04 Module and service pathConfirm which modules, power supplies and receiving cards can be removed from the front.
Wall-mounted indoor commercial LED display during installation
Wall-mounted installation with the cabinet grid exposed.

Which Commercial Indoor LED Display Components Can Be Serviced from the Front?

Front service usually covers the module, the power supply and the receiving card, but the exact scope changes by series. Ehonor, PS, CPS and Uni all list front-service access; confirm whether the power supply and receiving card are reachable from the front on the specific cabinet, and whether a spare module can be replaced without removing the cabinet. If the wall has rear access, a rear-service route can be simpler and less expensive; if it does not, front service is a design requirement.

How Do You Plan Power, Ventilation and Responsibility for a Commercial Indoor LED Display?

Scope Excel LED supply Local installer or consultant
Wall load and structural approval Cabinet weights, anchor points and frame loads Confirm wall capacity, method and sign-off
Shop drawing Cabinet layout, power and signal diagram Confirm site dimensions and conditions
Cabinets, modules, PSU, cards Supply, assemble and test Receive, inspect and store on site
Processor and control Supply and configure if ordered Provide sources, network and control position
Steel structure or bracket Supply and draw if ordered Install or fabricate locally; confirm finish
Cables and power distribution Supply specified cables if ordered Route, terminate and label
Installation labor Remote guidance if included Site labor, access equipment and safety

Use the indoor LED display installation guide for the site sequence. The video below shows a cabinet moving from packaging to the wall; it is useful for planning the delivery route and the number of people needed on site, not as a substitute for the project drawing.

Video: UNIFYLED, “Box to Wall: Unboxing a LED Cabinet, Retail-Ready”.

Request an Installation Review

07 — Technology comparison

Is an Indoor Commercial LED Display Better Than an LCD Video Wall?

Neither technology wins in every room. An LCD video wall is often the lower-cost route at 1080p and a familiar size; an LED wall removes the bezel grid, scales to custom dimensions and can be brighter. The decision should include the viewing distance, the content, the wall shape and the maintenance model, not just the purchase price.

Factor Indoor commercial LED display LCD video wall
Image continuity No bezel between cabinets; one continuous canvas Visible seams between panels; seam width depends on the model
Size and shape Built to the opening in cabinet increments; portrait, curved and custom shapes Standard panel sizes; the wall is a grid of fixed panels
Brightness Can run high nits and dim smoothly; check low-brightness grayscale Limited peak brightness; strong in controlled light
Close-view resolution Depends on pitch; P1.2 and below can match close-view text High pixel density at 1080p or 4K panel resolution
Service Module, PSU and card replacement; front or rear access depends on design Panel replacement; a failed panel may affect a larger area
Budget Wider range by pitch, cabinet and control; larger walls need structural work Often lower at 1080p; compare the full installed cost
Choose an indoor commercial LED display when: the wall is large or custom-shaped, seams are not acceptable, the room has high ambient light, or the screen must be viewed from several angles. Confirm the pitch against the nearest viewer.
Choose an LCD video wall when: the budget is fixed, the target is a standard 1080p grid, the room is controlled, and a panel seam is acceptable. Confirm the service model before comparing prices.

The indoor LED display vs LCD video wall comparison covers the five-year cost and brightness questions in more detail. For a projector comparison, use the LED display vs projector guide.

08 — Budget

What Does an Indoor Commercial LED Display Project Cost in 2026?

An indoor commercial LED display is quoted as a configuration, not as one price per square metre. The display package is the largest line, but the control system, structure, freight, installation and spares change the total. Use the ranges below for early planning, then ask for an itemized quotation with the cabinet count, pixel matrix and scope written out.

What Drives the Cost of a Commercial Indoor LED Display?

Cost line What changes it What to ask for
LED cabinets and modules Pitch, cabinet material, encapsulation and cabinet count Model, cabinet size, module size and quantity
Control system Processor, sending card, receiving cards, pixel capacity and redundancy Model, pixel capacity and spare cards
Content system Media player, software licence, cloud subscription and network hardware What is included; what is subscription-based
Structure Wall bracket, steel frame, base, corners and curves Drawing, finish and installation responsibility
Power and signal Power supplies, distribution, cables, UPS and network Circuit plan, cable schedule and termination
Spare parts Modules, receiving cards and power supplies Spare list and percentage
Packing and freight Export packing, Incoterm, destination and insurance Packing type, Incoterm and delivered scope
Services Commissioning, training, installation support and warranty Scope, duration and response path

What Does a Commercial Indoor LED Display Cost per Square Metre?

Pitch band 2026 planning range, display package Typical commercial use
P1.2–P1.5 USD 800–1,500 per m² Premium retail, close-view showroom, boardroom
P1.8–P2.5 USD 400–800 per m² Mainstream retail, lobby, mall feature wall
P2.9–P3.9 USD 200–400 per m² Large atrium, distance viewing, value wall

Ranges are from the Excel LED indoor LED display price guide, 2026. They cover the display package and change with cabinet, encapsulation, control and date. They are not a quotation and do not include structure, freight, installation or spares.

Planning example, not a quote: a 4 × 3 m P2.5 wall is 12 m². At USD 400–800 per m² for the display package, the cabinet and module line is about USD 4,800–9,600. Add the processor or player, structure, freight, installation and spares to reach the installed budget.

What Should a Commercial Indoor LED Display Quotation Include?

  • Cabinet model, cabinet size, pixel pitch and cabinet count.
  • Module size, module resolution and final wall pixel matrix.
  • Power supply, receiving card and sending card models; spare quantities.
  • Processor or media player model, pixel capacity and input types.
  • Structure drawing, finish and the split between factory supply and local work.
  • Packing type, Incoterm, freight, insurance and destination.
  • Commissioning, training, warranty and the response path.
  • Lead time, payment terms and the date of the price.

Request an Itemized Quote

09 — Project evidence

Which Indoor Commercial LED Display Projects Show Real Deployment Evidence?

Evidence for a commercial display should include the project record, the configuration and what was actually installed. Excel LED publishes project records; where a record does not state a size or series, this page does not invent one. The three records below are a starting point for a reference call, not a claim that every project matches your brief.

Which Indoor Commercial LED Display Project Records Can You Review?

Portrait P2.5 indoor commercial LED display in a Lagos shopping mall
Lagos mall portrait screen (project record image).

Lagos, Nigeria

P2.5 Portrait Mall Screen

A portrait P2.5 indoor display running branded content in a Lagos shopping mall. The project record lists the P2.5 pitch and portrait format; confirm the final cabinet size and control route with the project team. View the case library.

Airport departure hall LED information displays
Airport departure-hall reference image; see the project record.

Doha, Qatar

P3.9 Airport Information Wall, 28 m²

A completed P3.9 LED screen in an airport departure hall, used as an information wall. The project record states 28 m² and the departure-hall setting. Read the Doha project record.

Conference room indoor LED display wall
Berlin conference reference image.

Berlin, Germany

P2.5 Conference Wall, 40 m²

A completed P2.5 indoor event wall for a conference setting in Berlin. The record states 40 m² and the event use. Read the Berlin project record.

Which Indoor Commercial LED Display Reference Installations Show Common Layouts?

The images below are reference installations, not named client projects. They show the kind of mounting, viewing distance and screen proportion a commercial brief can use. Use them to start a layout conversation; ask for a project record when you need a verifiable reference in your region.

Indoor commercial LED display in a restaurant dining area
Hospitality reference installation.

Restaurant and Café

Wall used for atmosphere, menus and seasonal campaigns.

Indoor commercial LED display above a shopping mall entrance
Mall entrance reference installation.

Mall Entrance

Ribbon display over a circulation route during commissioning.

Reference showroom installation of a large indoor commercial LED display
Showroom reference installation.

Showroom

Dark showroom with a large wall and a second display for detail content.

Reference lobby installation of a wide indoor commercial LED display
Lobby reference installation.

Corporate Lobby

Wide wall in a reception or lobby with a low-brightness content loop.

For more records, use the LED display case studies and the project video center. When you request a reference, state your country, application and nearest viewing distance so the project team can match the case.

Ask for a Project Reference

10 — Factory and support

How Does Excel LED Support Indoor Commercial LED Display Projects from Drawing to After-Sales?

Support starts before the cabinet order. The project team reviews the wall drawing, the pixel load, the control route and the installation scope, then releases the cabinet layout for approval. The factory assembles and tests the cabinets, ages the wall, packs the order and supplies the documents needed for import and commissioning. The exact scope is written into the order; do not assume that every service is included in every price.

  1. Brief review: confirm the application, nearest viewer, wall size, content and service route.
  2. Drawing and BOM: issue the cabinet layout, pixel matrix, power and signal plan, and the itemized bill of materials.
  3. Production and test: assemble cabinets, run module and cabinet tests, and age the display before packing.
  4. Packing and documents: export packing, packing list, test record, warranty terms and spare list.
  5. Commissioning and after-sales: remote guidance, spare parts, replacement procedure and the named support contact.
Document What it should show
Cabinet drawing Cabinet size, count, pixel matrix, mounting points and service access
Power and signal plan Circuits, cable routes, sending and receiving hardware, pixel capacity
Test record Module test, cabinet test, aging result and any agreed inspection points
Packing list Cabinet, module, power supply, card, cable and spare quantities
Warranty and spare list Cover period, response path, spare percentage and replacement procedure

Certification has to be checked per model and per market. A company certificate is not proof that every cabinet, power supply or configuration meets the destination requirement. Ask for the file that matches the model and the market you are importing into. For the factory process, see Excel LED screen manufacturing and the LED display manufacturing process.

11 — Buyer questions

What Do Buyers Ask Most About Indoor Commercial LED Displays?

These are the questions that most often change a commercial quotation. The answers give a direct planning position and the condition that can change it.

How much does an indoor commercial LED display cost?
For early planning in 2026, the display package is commonly quoted at USD 800–1,500 per m² for P1.2–P1.5, USD 400–800 per m² for P1.8–P2.5, and USD 200–400 per m² for P2.9–P3.9. Those ranges exclude control, structure, freight, installation and spares. A 12 m² P2.5 wall at USD 400–800 per m² is about USD 4,800–9,600 for the display package. Ask for an itemized quote with the cabinet count and scope.
Which pixel pitch should I choose for a retail store?
Start with the nearest viewer. For a 2–4 m viewing distance, P1.5–P2.5 is the usual band; for a window where people stand within 2 m, compare P1.5–P2.0. If the screen shows small price text or product detail, move one step finer. If it only shows large campaign video at 5 m, a larger pitch can be the lower-cost choice. Confirm the content and the closest standing position before fixing the pitch.
Can an indoor commercial LED display fit a custom wall or portrait layout?
Yes. The wall is built from cabinets, so the final size follows the cabinet grid rather than a fixed television size. Portrait layouts are possible; the cabinet can be rotated if the module and receiving-card layout support it. Send the elevation, the opening depth and the nearest viewer. The supplier should return a cabinet layout and the final pixel matrix, not just a diagonal size.
Can staff update advertising content remotely?
It depends on the player, software and network included in the order. A local player can be updated on site; a networked player can receive scheduled content from an office; a cloud CMS can manage several sites. Confirm the player model, licence, network access, fallback playback and who has permission to publish. Remote management is a configuration, not a standard feature of every screen.
What is required to manage displays across multiple stores?
A multi-site setup needs compatible players at each store, a central CMS, network access, role permissions, a content approval workflow and a fallback plan for network loss. Confirm how the CMS handles offline playback, logs and emergency content. Ask for a pilot store before rolling out to the chain, and define who owns content, hardware and support in each country.
Which components can be serviced from the front?
On the front-service series, the module, power supply and receiving card are the usual service items. The exact scope changes by cabinet: confirm that the power supply and card are reachable from the front, and that a spare module can be replaced without removing the cabinet. If the wall has rear access, a rear-service design can be simpler. Put the service route in the drawing before production.
What information is needed for a complete project quotation?
Send the application, wall width and height, installation location and a site photo, nearest and farthest viewing distance, content type, destination country, target installation date and budget range. Add the wall construction, available depth, power supply and whether rear access exists. A drawing or elevation is more useful than a description; it lets the supplier return a cabinet layout instead of a generic price.
What warranty, spare parts and installation support are included?
The scope is set in the order. Ask for the warranty period, what it covers, the response path, the spare module, card and power-supply quantities, and whether installation guidance is remote or on site. Confirm the spare percentage and the replacement procedure. Certification and warranty should be checked per model and destination market; a general company certificate is not a substitute.

Request a Configuration Answer

12 — Request a configuration

How Do You Request an Indoor Commercial LED Display Configuration?

A useful inquiry gives the supplier enough information to return a cabinet layout, a pixel matrix and an itemized quote. You do not need a final specification; the project team can propose a route. Send the inputs below and state which decisions are still open.

What Should You Send With an Indoor Commercial LED Display Inquiry?

Input Why it matters Required or optional
Application and content Sets pitch, brightness and control route Required
Wall width × height Sets cabinet grid and pixel matrix Required
Site photo or elevation Shows the opening, access and surrounding light Required if available
Nearest viewing distance Sets the pitch band Required
Installation location and depth Sets bracket, recess and service route Required
Destination country and date Sets freight, certification and lead time Required
Budget range Helps compare routes without over-specifying Optional
Content samples Shows text size, frame rate and aspect ratio Optional

You will receive a cabinet layout, the final pixel matrix, an itemized quotation, the control and content route, the lead time and the document list. If the wall is not a standard rectangle, include the corner or curve detail so the frame and cabinet grid can be checked before production.

Request an Indoor Commercial LED Display Configuration

Send the wall size, nearest viewer, content type and destination. The project team will return a cabinet layout and an itemized quotation.

Get My Recommended Configuration

13 — Next reads

Which Indoor Commercial LED Display Resources Should You Read Next?

Use these pages when you need a deeper technical or commercial answer. Each one covers a different decision, so you do not have to repeat the same search.

For a broader commercial comparison, use the shopping mall LED display solution and the hotel LED display solution. For the manufacturer profile, see LED display manufacturer.

Wall-mounted installation planning: It explains how to plan a commercial wall around the surveyed substrate, service route and viewing positions. See the wall-mounted commercial LED display.

Scroll to Top

Contact Us Now!

Thank You for Your Inquiry!

 Our LED display expert will contact you within 12 hours.

You can also contact us directly: +86 18569492693 ;excelledscreens@gmail.com